Clock Archives - Elevator Sound https://www.elevatorsound.com/product-category/modular/modular-utility/modular-clock/ Eurorack Modular, Synthesizer & Electronic Music Hardware Store Wed, 11 Dec 2024 10:28:44 +0000 en-GB hourly 1 https://wordpress.org/?v=6.7.1 Instruo Gloc Eurorack Clock Generator Processor Module https://www.elevatorsound.com/product/instruo-gloc-eurorack-clock-generator-processor-module/ Thu, 05 Dec 2024 12:00:23 +0000 https://www.elevatorsound.com/?post_type=product&p=94532 Introducing gloc, a clock generator and processor. Capable of turning a single internal/external clock input into a stream of related clock sources. Predictable division/multiplication, complex trigger/gate sequences via probabilistic masking – or any combination of both across each of its 7 clock pulse outputs. Onboard dynamic phase alignment, smart tap tempo detection and locked vs live modes make gloc excellent for performative and generative temporal exploration! Features Tap tempo clock generator 1 clock input to 7 output Clock processor Manual or CV control over the spread of clock divisions/multiplications Probabilistic “coin-toss” logic for random phrasing Probabilistic density masking for repeated phrasing Manual Pulse width control over Clock Pulse outputs Dedicated Clock Reset input Live and Lockable Clock output states Smart tempo follower and manual button Save and recall settings between power cycles Specifications Width: 4hp Depth: 31mm Power: +12v 75mA / -12v 0mA Manufacturer product page here. Product manual here.

The post Instruo Gloc Eurorack Clock Generator Processor Module appeared first on Elevator Sound.

]]> Introducing gloc, a clock generator and processor. Capable of turning a single internal/external clock input into a stream of related clock sources. Predictable division/multiplication, complex trigger/gate sequences via probabilistic masking – or any combination of both across each of its 7 clock pulse outputs.

Onboard dynamic phase alignment, smart tap tempo detection and locked vs live modes make gloc excellent for performative and generative temporal exploration!

Features

  • Tap tempo clock generator
  • 1 clock input to 7 output Clock processor
  • Manual or CV control over the spread of clock divisions/multiplications
  • Probabilistic “coin-toss” logic for random phrasing
  • Probabilistic density masking for repeated phrasing
  • Manual Pulse width control over Clock Pulse outputs
  • Dedicated Clock Reset input
  • Live and Lockable Clock output states
  • Smart tempo follower and manual button
  • Save and recall settings between power cycles

Specifications

  • Width: 4hp
  • Depth: 31mm
  • Power: +12v 75mA / -12v 0mA

Manufacturer product page here.
Product manual here.

The post Instruo Gloc Eurorack Clock Generator Processor Module appeared first on Elevator Sound.

]]> Doepfer A-165-2 Eurorack Digital Gate/Trigger Modifier Module https://www.elevatorsound.com/product/doepfer-a-165-2-eurorack-digital-gate-trigger-modifier-module/ Mon, 08 Jul 2024 21:06:40 +0000 https://www.elevatorsound.com/?post_type=product&p=91891 The Digital Modifier A-165-2 from Doepfer can derive various switching signals from two trigger or gate signals. The A-165-2 is a smaller and optimized version of Doepfer’s Trigger Modifier, which is no longer available. The two inputs are intended for trigger, gate or clock signals, i.e. everything for which the term digital signals can also be used. The outputs provide various states derived from the inputs. The module is ideal for start/stop signals, signal inversion, frequency halving or converting a signal into a trigger. The module only accepts unipolar signals. Incoming bipolar signals are clipped. The outputs work as follows: Inverted signal to input 1 Inverted signal to input 2 T flip-flop (toggle flip-flop), controlled by input 1, this output changes its state on the rising edge of input 1 Set/reset flip-flop, this output changes its state to “high” on the rising edge of input 1 and goes to “low” on the rising edge of input 2 Inverted output of the set/reset flip-flop, this output changes its state to “low” on the rising edge of input 1 and goes to “high” on the rising edge of input 2 Pulse output, a trigger pulse of approx. 50 ms in length is […]

The post Doepfer A-165-2 Eurorack Digital Gate/Trigger Modifier Module appeared first on Elevator Sound.

]]> The Digital Modifier A-165-2 from Doepfer can derive various switching signals from two trigger or gate signals.

The A-165-2 is a smaller and optimized version of Doepfer’s Trigger Modifier, which is no longer available. The two inputs are intended for trigger, gate or clock signals, i.e. everything for which the term digital signals can also be used. The outputs provide various states derived from the inputs.

The module is ideal for start/stop signals, signal inversion, frequency halving or converting a signal into a trigger. The module only accepts unipolar signals. Incoming bipolar signals are clipped.

    The outputs work as follows:
  • Inverted signal to input 1
  • Inverted signal to input 2
  • T flip-flop (toggle flip-flop), controlled by input 1, this output changes its state on the rising edge of input 1
  • Set/reset flip-flop, this output changes its state to “high” on the rising edge of input 1 and goes to “low” on the rising edge of input 2
  • Inverted output of the set/reset flip-flop, this output changes its state to “low” on the rising edge of input 1 and goes to “high” on the rising edge of input 2
  • Pulse output, a trigger pulse of approx. 50 ms in length is generated on both the rising and falling edge of the signal applied to input 1

      • Specifications
      Width: 2hp
      Depth: 45mm
      Power: +30mA, -0mA
      Manufacturer product page here.

      The post Doepfer A-165-2 Eurorack Digital Gate/Trigger Modifier Module appeared first on Elevator Sound.

      ]]> Frap Tools Bagai Eurorack Random Noise/Clock Module https://www.elevatorsound.com/product/frap-tools-bagai-eurorack-random-noise-clock-module/ Tue, 14 May 2024 15:02:04 +0000 https://www.elevatorsound.com/?post_type=product&p=90506 Bagai is an analog sample and hold, bit crusher, and down sampler, also capable of generating fluctuating random voltages, coloured noise, and clock bursts. It consists of six highly intertwined sections: A clock with straight and random outputs (yellow) An analog noise generator with variable color (grey) A bipolar fluctuating random voltage generator (white) with variable rate A sample and hold the circuit (orange) with selectable time scale, slow for modulation, or fast for audio sampling up to 34 kHz. An 8-bit quantized version of the orange S&H circuit with variable bit depth (red) A clock burst section (green). By default, it outputs bipolar random voltages and triggers. The voltages are fluctuating, stepped, and quantized with selectable bit depth. The clocks are straight, randomized, or “burst”.Once you start patching, you can use it as a S&H, audio downsampled, and bitcrusher, with a sample rate of 30 kHz. All its major parameters are voltage controllable. Features Sample and Hold with an 8-Bit Quantizer – Bagài features two stepped S&H circuits with open input (semi-normalled by default to an analog noise source). The quantized one has a LSB selector that defines its bit depth, from 1 to 8 bits Random Triggers & […]

      The post Frap Tools Bagai Eurorack Random Noise/Clock Module appeared first on Elevator Sound.

      ]]>       Bagai is an analog sample and hold, bit crusher, and down sampler, also capable of generating fluctuating random voltages, coloured noise, and clock bursts. It consists of six highly intertwined sections:

      • A clock with straight and random outputs (yellow)
      • An analog noise generator with variable color (grey)
      • A bipolar fluctuating random voltage generator (white) with variable rate
      • A sample and hold the circuit (orange) with selectable time scale, slow for modulation, or fast for audio sampling up to 34 kHz.
      • An 8-bit quantized version of the orange S&H circuit with variable bit depth (red)
      • A clock burst section (green).

      By default, it outputs bipolar random voltages and triggers. The voltages are fluctuating, stepped, and quantized with selectable bit depth. The clocks are straight, randomized, or “burst”.Once you start patching, you can use it as a S&H, audio downsampled, and bitcrusher, with a sample rate of 30 kHz. All its major parameters are voltage controllable.

      Features

      • Sample and Hold with an 8-Bit Quantizer – Bagài features two stepped S&H circuits with open input (semi-normalled by default to an analog noise source). The quantized one has a LSB selector that defines its bit depth, from 1 to 8 bits
      • Random Triggers & Clock Bursts – Besides the well-known “main,” “more than,” and “less than” modes, Bagài also features a clock burst circuit that creates super fast and unpredictable streams of gates that you can combine with the main clock or to any other trigger you want.
      • Voltage-Controllable Bitcrusher – When used with audio signals, the 8-bit quantized S&H becomes a warm bitcrusher effect with voltage-controllable bit depth!
      • Dynamic Downsampler – Bagài’s internal clock can switch to an audio rate mode going up to 34 kHz. Patching audio signals into the S&H input will transform Bagài into an analog audio downsampler.
      • Open Signal Path – Lots of semi-normalled connections allow you to use Bagài in infinite ways: cross-patching has never been this fun.
      • Start and Stop Controls – You can control both the main clock and the clock bursts via external gates. The main clock also features a button to manually hold it.
      • Analog Noise – At Bagài’s core is a thermal noise generator that feeds the S&H circuit, creating random voltage streams. The noise output features a knob that changes its color, emphasizing the high or low frequencies.
      • Fluctuating Random Voltages and Global Rate of Change – The feature we all loved on Sapèl, now bipolar and with extended range.

      Specifications

      • Width: 12hp
      • Depth: 38mm
      • Power: +190mA, -90mA

      Manufacturer product page here.
      Product manual here.

      The post Frap Tools Bagai Eurorack Random Noise/Clock Module appeared first on Elevator Sound.

      ]]>             Doepfer A-161 Eurorack Clock Sequencer Module (A-160 Expander) https://www.elevatorsound.com/product/doepfer-a-161-eurorack-clock-sequencer-module-a-160-expander/ Tue, 16 Apr 2024 13:05:33 +0000 https://www.elevatorsound.com/?post_type=product&p=89794 Module A-161 is an eight-step Clock Sequencer which is internally connected to the Clock Divider (A-160). Eight outputs are sequentially switched by the clock signals from the A-160 (see Fig. 1) and can act, for instance, as sequential rhythmic triggers for an envelope. The reset on the A-160 also works on the A-161 (instant return to Step 1). The low/high levels of the output signals are 0V and about +10V. In combination with a mixer (A-138) short analog sequences can be generated. The A161 draws its current via the A160 module, which MUST be fitted directly to the left of the A161. The A161 CANNOT function without the A160. Specifications Width: 4hp Depth: 40mm Power: +20mA, -0mA Manufacturer product page here. Product manual here.

      The post Doepfer A-161 Eurorack Clock Sequencer Module (A-160 Expander) appeared first on Elevator Sound.

      ]]>       Module A-161 is an eight-step Clock Sequencer which is internally connected to the Clock Divider (A-160). Eight outputs are sequentially switched by the clock signals from the A-160 (see Fig. 1) and can act, for instance, as sequential rhythmic triggers for an envelope. The reset on the A-160 also works on the A-161 (instant return to Step 1). The low/high levels of the output signals are 0V and about +10V. In combination with a mixer (A-138) short analog sequences can be generated.

      The A161 draws its current via the A160 module, which MUST be fitted directly to the left of the A161. The A161 CANNOT function without the A160.

      Specifications
      Width: 4hp
      Depth: 40mm
      Power: +20mA, -0mA
      Manufacturer product page here.
      Product manual here.

      The post Doepfer A-161 Eurorack Clock Sequencer Module (A-160 Expander) appeared first on Elevator Sound.

      ]]>             Shakmat Modular Clock O’Pawn MKII Eurorack Clock Generator Module https://www.elevatorsound.com/product/shakmat-modular-clock-opawn-mkii-eurorack-clock-generator-module/ Mon, 18 Dec 2023 16:40:41 +0000 https://www.elevatorsound.com/?post_type=product&p=86640 The Clock O’Pawn mk2 serves as a versatile clock device, taking on the role of true “chef d’orchestre” for your modular system. Its transport section lets you start, stop, and reset instruments synchronized with its intuitive internal clock or have your setup dance with your MIDI equipment. If you find metronomic clock signals uninspiring, a variety of groove patterns and clock humanization features enable the maestro to guide your setup with distinctive shuffles and swings. To complete this rich set of features in a small yet powerful clock source: presets memory, select bus compatibility, and several handy options to configure the Clock O’Pawn the way it suits you the best. Features Clock source module offering four distinct outputs Transport section with play, pause, stop, tap tempo and manual reset operations Diverse selection of grooves, ranging from classic swing to experimental clock manipulation Humanize adding randomisation to the clock timing Accent output with 27 different patterns Option menu for customizable preferences Midi input for external sync with midi devices Memory of 16 presets Specifications Width: 6hp Depth: 27mm Power: +55mA, -0mA Manufacturer product page here. Product manual here.

      The post Shakmat Modular Clock O’Pawn MKII Eurorack Clock Generator Module appeared first on Elevator Sound.

      ]]>       The Clock O’Pawn mk2 serves as a versatile clock device, taking on the role of true “chef d’orchestre” for your modular system. Its transport section lets you start, stop, and reset instruments synchronized with its intuitive internal clock or have your setup dance with your MIDI equipment.

      If you find metronomic clock signals uninspiring, a variety of groove patterns and clock humanization features enable the maestro to guide your setup with distinctive shuffles and swings. To complete this rich set of features in a small yet powerful clock source: presets memory, select bus compatibility, and several handy options to configure the Clock O’Pawn the way it suits you the best.

      Features

      • Clock source module offering four distinct outputs
      • Transport section with play, pause, stop, tap tempo and manual reset operations
      • Diverse selection of grooves, ranging from classic swing to experimental clock manipulation
      • Humanize adding randomisation to the clock timing
      • Accent output with 27 different patterns
      • Option menu for customizable preferences
      • Midi input for external sync with midi devices
      • Memory of 16 presets

      Specifications
      Width: 6hp
      Depth: 27mm
      Power: +55mA, -0mA
      Manufacturer product page here.
      Product manual here.

      The post Shakmat Modular Clock O’Pawn MKII Eurorack Clock Generator Module appeared first on Elevator Sound.

      ]]>             BeepBoop Electronics CLK DIV Eurorack Clock Divider Module https://www.elevatorsound.com/product/beepboop-electronics-clk-div-eurorack-clock-divider-module/ Mon, 04 Dec 2023 17:55:39 +0000 https://www.elevatorsound.com/?post_type=product&p=86232 A 2hp clock divider module with an internal tap tempo. The tap tempo output is normalized to the clock divider input ready to be divided down. Alternatively an external clock can be divided down. The tap tempo section works great for manually creating a tempo for your modular patch to jam with. Divide by 1, 2, 4 and 8 and also choose between trigger and gate output mode. The upper button is used to trigger the tap tempo, the circuit requires just two taps to generate a steady clock / gate. The lower two buttons are used to toggle through and select the clock division. You can choose from 1/2/4/8 divisions. The LED display for the DIV count is as follows. Orange – DIV 0 Red – DIV 2 Green – DIV 4 Blank – DIV 8 The CLK divider can output either gates or Triggers. The orange LED behind indicates if the output is in Gate or Trig mode. On – Trig Off- Gate Lovingly hand built at Beepboop Electronics workshop in Bristol Specifications Width: 2hp Depth: 25mm Power: +20mA, -0mA Manufacturer product page here.

      The post BeepBoop Electronics CLK DIV Eurorack Clock Divider Module appeared first on Elevator Sound.

      ]]>       A 2hp clock divider module with an internal tap tempo. The tap tempo output is normalized to the clock divider input ready to be divided down. Alternatively an external clock can be divided down. The tap tempo section works great for manually creating a tempo for your modular patch to jam with.

      Divide by 1, 2, 4 and 8 and also choose between trigger and gate output mode. The upper button is used to trigger the tap tempo, the circuit requires just two taps to generate a steady clock / gate. The lower two buttons are used to toggle through and select the clock division. You can choose from 1/2/4/8 divisions.

      The LED display for the DIV count is as follows.
      Orange – DIV 0
      Red – DIV 2
      Green – DIV 4
      Blank – DIV 8

      The CLK divider can output either gates or Triggers.
      The orange LED behind indicates if the output is in Gate or Trig mode.
      On – Trig
      Off- Gate

      Lovingly hand built at Beepboop Electronics workshop in Bristol

      Specifications
      Width: 2hp
      Depth: 25mm
      Power: +20mA, -0mA
      Manufacturer product page here.

      The post BeepBoop Electronics CLK DIV Eurorack Clock Divider Module appeared first on Elevator Sound.

      ]]>             Xaoc Devices Drezno II Eurorack ADC/DAC Binary Module https://www.elevatorsound.com/product/xaoc-devices-drenzo-ii-eurorack-adc-dac-binary-module/ Tue, 08 Aug 2023 14:00:25 +0000 https://www.elevatorsound.com/?post_type=product&p=81719 Drezno II is an improved version of the original Drezno module. It is an essential member of the 8-bit Xaoc Devices Leibniz Binary Subsystem. The Leibniz subsystem is a family of modules that operate on 8 binary (two-state, on/off) signals. These signals are arranged as 8 bits of digital data and may represent analog signals and voltages, or they may be whatever you want them to be (clocks, gates, rhythms, etc.). Drezno features an ADC (analog-to-digital-converter) and DAC (digital-to-analog-converter), allowing it to act as an analog front-end of the system. In other words, Drezno allows one to convert analog signals and CVs into digital numbers, as well as to obtain analog signals back from some other digital numbers (or 8 binary signals). Between these two conversions there is a whole universe of digital shenanigans waiting to happen resulting in all kinds of signal transformations and modulations. Both (ADC and DAC) sections of Drezno can work independently, or they can be linked. Input and output range of analog signals may be adjusted using Gain and Offset sliders. Individual bit outputs (for the ADC) and inputs (DAC) allow for extensive cross-patching and the creation of complex waveforms and rhythms. A very fast […]

      The post Xaoc Devices Drezno II Eurorack ADC/DAC Binary Module appeared first on Elevator Sound.

      ]]>       Drezno II is an improved version of the original Drezno module. It is an essential member of the 8-bit Xaoc Devices Leibniz Binary Subsystem. The Leibniz subsystem is a family of modules that operate on 8 binary (two-state, on/off) signals. These signals are arranged as 8 bits of digital data and may represent analog signals and voltages, or they may be whatever you want them to be (clocks, gates, rhythms, etc.).

      Drezno features an ADC (analog-to-digital-converter) and DAC (digital-to-analog-converter), allowing it to act as an analog front-end of the system. In other words, Drezno allows one to convert analog signals and CVs into digital numbers, as well as to obtain analog signals back from some other digital numbers (or 8 binary signals). Between these two conversions there is a whole universe of digital shenanigans waiting to happen resulting in all kinds of signal transformations and modulations.

      Both (ADC and DAC) sections of Drezno can work independently, or they can be linked. Input and output range of analog signals may be adjusted using Gain and Offset sliders. Individual bit outputs (for the ADC) and inputs (DAC) allow for extensive cross-patching and the creation of complex waveforms and rhythms. A very fast clock (up to 2MHz) at which the conversions are performed may be replaced with any external clock (for each section separately).

      Compared to its predecessor, Drezno II uses new converters of much higher resolution which results in much lower noise floor and higher accuracy. The lower bits are much more stable than before. It is easy now to use Drezno for quantizing pitch voltages with accurate results with 128 or 256 semitone steps. Potentiometer ranges are factory calibrated for precise chromatic scale. A new switch on the front panel allows the user to select the calibrated range of 10Vpp or 20Vpp, so that the lowest bit or the second bit correspond to 1 semitone.

      Specifications
      Width: 12hp
      Depth: ~40mm (TBC)
      Power: 80mA +12V | 50mA -12V
      Manufacturer product page here.
      Product manual here.

      The post Xaoc Devices Drezno II Eurorack ADC/DAC Binary Module appeared first on Elevator Sound.

      ]]>             AtoVproject Gaeto Eurorack Clock Divider and Logic Module (Black) https://www.elevatorsound.com/product/atovproject-gaeto-eurorack-clock-divider-and-logic-module-black/ Mon, 31 Jul 2023 15:43:22 +0000 https://www.elevatorsound.com/?post_type=product&p=81505 The AtoVproject Gaeto is a new type of clocked logic module. Gaeto is a great module to play around with triggers, gates and legatoes turning one into the other. As a result we decided to name the module Gaeto from “Gate” and “Legato”. Some of the functions that the module can perform are: /2 /3 Clock divider Legato generator Trigger to gate converter Rhythm quantiser Sub octave generator with PWM Generative trigger sequencer The Gaeto’s function is to perform the following operation: “If the signal on the data input has been high, then the output is high at the next clock. If not – the non-output is high.” In other words, if the signal on the input signal goes over 1V then the memory stores a 1 if not it stores a 0. At the next clock the output will be high if a 1 was stored and the non output will be high if a 0 was stored. The output is coupled with an AND gate that allows for the outputs to either follow the pulse width of the clock or be maintained high until the next clock. This function is also CV controllable for interesting rhythm modulations. This […]

      The post AtoVproject Gaeto Eurorack Clock Divider and Logic Module (Black) appeared first on Elevator Sound.

      ]]>       The AtoVproject Gaeto is a new type of clocked logic module. Gaeto is a great module to play around with triggers, gates and legatoes turning one into the other. As a result we decided to name the module Gaeto from “Gate” and “Legato”.

      Some of the functions that the module can perform are:

      • /2 /3 Clock divider
      • Legato generator
      • Trigger to gate converter
      • Rhythm quantiser
      • Sub octave generator with PWM
      • Generative trigger sequencer

      The Gaeto’s function is to perform the following operation:
      “If the signal on the data input has been high, then the output is high at the next clock. If not – the non-output is high.”

      In other words, if the signal on the input signal goes over 1V then the memory stores a 1 if not it stores a 0. At the next clock the output will be high if a 1 was stored and the non output will be high if a 0 was stored.

      The output is coupled with an AND gate that allows for the outputs to either follow the pulse width of the clock or be maintained high until the next clock. This function is also CV controllable for interesting rhythm modulations.

      This rather obscure function allows for an extremely wide range of uses. This is a module that rewards exploration.

      Additionally, multiple Gaetos can be chained together using the included cable to create shift register functions.

      This design relies on CMOS CD4000 series ICs (4013 and 4081). These were selected for their reliability, high speed and low power consumption.

      The Module is available with either Grey or Black panels, assembled or as a DIY kit.

      Specifications

      • Width: 6hp
      • Depth: 20mm
      • Power: +24mA / -12mA

      Manufacturer product page here.
      Product manual here.

      The post AtoVproject Gaeto Eurorack Clock Divider and Logic Module (Black) appeared first on Elevator Sound.

      ]]>             AtoVproject Gaeto Eurorack Clock Divider and Logic Module (Silver) https://www.elevatorsound.com/product/atovproject-gaeto-eurorack-clock-divider-and-logic-module-silver/ Mon, 31 Jul 2023 15:43:39 +0000 https://www.elevatorsound.com/?post_type=product&p=81508 The AtoVproject Gaeto is a new type of clocked logic module. Gaeto is a great module to play around with triggers, gates and legatoes turning one into the other. As a result we decided to name the module Gaeto from “Gate” and “Legato”. Some of the functions that the module can perform are: /2 /3 Clock divider Legato generator Trigger to gate converter Rhythm quantiser Sub octave generator with PWM Generative trigger sequencer The Gaeto’s function is to perform the following operation: “If the signal on the data input has been high, then the output is high at the next clock. If not – the non-output is high.” In other words, if the signal on the input signal goes over 1V then the memory stores a 1 if not it stores a 0. At the next clock the output will be high if a 1 was stored and the non output will be high if a 0 was stored. The output is coupled with an AND gate that allows for the outputs to either follow the pulse width of the clock or be maintained high until the next clock. This function is also CV controllable for interesting rhythm modulations. This […]

      The post AtoVproject Gaeto Eurorack Clock Divider and Logic Module (Silver) appeared first on Elevator Sound.

      ]]>       The AtoVproject Gaeto is a new type of clocked logic module. Gaeto is a great module to play around with triggers, gates and legatoes turning one into the other. As a result we decided to name the module Gaeto from “Gate” and “Legato”.

      Some of the functions that the module can perform are:

      • /2 /3 Clock divider
      • Legato generator
      • Trigger to gate converter
      • Rhythm quantiser
      • Sub octave generator with PWM
      • Generative trigger sequencer

      The Gaeto’s function is to perform the following operation:
      “If the signal on the data input has been high, then the output is high at the next clock. If not – the non-output is high.”

      In other words, if the signal on the input signal goes over 1V then the memory stores a 1 if not it stores a 0. At the next clock the output will be high if a 1 was stored and the non output will be high if a 0 was stored.

      The output is coupled with an AND gate that allows for the outputs to either follow the pulse width of the clock or be maintained high until the next clock. This function is also CV controllable for interesting rhythm modulations.

      This rather obscure function allows for an extremely wide range of uses. This is a module that rewards exploration.

      Additionally, multiple Gaetos can be chained together using the included cable to create shift register functions.

      This design relies on CMOS CD4000 series ICs (4013 and 4081). These were selected for their reliability, high speed and low power consumption.

      The Module is available with either Grey or Black panels, assembled or as a DIY kit.

      Specifications

      • Width: 6hp
      • Depth: 20mm
      • Power: +24mA / -12mA

      Manufacturer product page here.
      Product manual here.

      The post AtoVproject Gaeto Eurorack Clock Divider and Logic Module (Silver) appeared first on Elevator Sound.

      ]]>             ALM Busy Circuits PPEXP2 Eurorack Pamela’s Pro Workout Expander Module https://www.elevatorsound.com/product/alm-busy-circuits-ppexp2-eurorack-pamelas-pro-workout-expander-module/ Wed, 18 Jan 2023 14:00:29 +0000 https://www.elevatorsound.com/?post_type=product&p=73026 PPEXP1 & PPEXP2 are two expander modules for Pamela’s PRO Workout that both offer additional dedicated fixed clock, Din Sync & MIDI clock outputs. Extend Pam as a master to clock external gear with super solid dedicated MIDI & Din Sync clock outputs. Use the extra fixed clocked gate outputs to free up Pam’s main outputs for unique sequencing or complex modulation duties. Connects directly to and is powered by the ‘MIDI-EX’ expander header on rear of Pamela’s PRO Workout. Only a single output expander is supported at any time but either can be used alongside an AXON-1 CV input expander. Adapter cables are available for connecting to DIN type connectors, for both MIDI and Din Sync. PPEXP 1 includes a MIDI Din adapter cable. Specifications Width: 2hp Depth: Power: Manufacturer product page here. Product manual here.

      The post ALM Busy Circuits PPEXP2 Eurorack Pamela’s Pro Workout Expander Module appeared first on Elevator Sound.

      ]]>       PPEXP1 & PPEXP2 are two expander modules for Pamela’s PRO Workout that both offer additional dedicated fixed clock, Din Sync & MIDI clock outputs.

      Extend Pam as a master to clock external gear with super solid dedicated MIDI & Din Sync clock outputs.

      Use the extra fixed clocked gate outputs to free up Pam’s main outputs for unique sequencing or complex modulation duties.

      Connects directly to and is powered by the ‘MIDI-EX’ expander header on rear of Pamela’s PRO Workout.

      Only a single output expander is supported at any time but either can be used alongside an AXON-1 CV input expander.

      Adapter cables are available for connecting to DIN type connectors, for both MIDI and Din Sync. PPEXP 1 includes a MIDI Din adapter cable.

      Specifications

      • Width: 2hp
      • Depth:
      • Power:

      Manufacturer product page here.
      Product manual here.

      The post ALM Busy Circuits PPEXP2 Eurorack Pamela’s Pro Workout Expander Module appeared first on Elevator Sound.

      ]]>